Bulgari Octo Finissimo QC: thickness, octagonal case and sandblasted titanium

The Octo Finissimo is a watch built around one number: thickness. And it is precisely the hardest number to copy, because it depends on the movement inside.

What the original is like, according to the reviews:

  • A sandblasted titanium case, 40 mm in diameter and 5.15 mm thick, sapphire glass front and back; water-resistant to 30 m.
  • Shape: octagonal, with many facets between bezel, caseband and lugs.
  • A titanium crown with a black ceramic insert.
  • A titanium dial, black hands; the whole watch has the same matte grey finish, from bracelet to dial.
  • Movement: calibre BVL 138, automatic with a platinum micro-rotor, only 2.23 mm thick, 60 hours of reserve.

[[PHOTO: Octo Finissimo in titanio di profilo accanto a un calibro digitale aperto a 5,15 mm, frecce sul vetro, sulla carrure e sul fondello]]

Not sure about thickness on a QC? Create an account and ask the community.

Editorial summary, not independently verified.

Simple question: why would thickness be so hard? It’s a case, you just make it thinner.

Not quite. A case’s thickness starts from the movement:

  • The original’s BVL 138 is 2.23 mm high, thanks to the micro-rotor set into the plane of the movement instead of a central rotor on top.
  • A traditional automatic with a central rotor is much taller. If a different movement is inside, the case must grow, or the proportions change somewhere.
  • One review also notes that the original movement is 36.6 mm across and almost fills the 40 mm case.

That is why the single most useful photo is a side view, with a calliper on the maximum thickness, glass included. An extra millimetre on a 5 mm watch shows at once, even by eye, if you compare the profile with reference photos.

Clear. And the finish? In the photos it just looks grey.

That is exactly the point: the sandblasted surface is matte and even, with no polished areas, and one review describes the grain as “neither too coarse nor too fine”. In QC photos, look for:

  • grain that is even on bezel, caseband, lugs and bracelet, with no shinier or rougher zones;
  • edges between the facets of the octagon that stay sharp, not rounded;
  • the same grey on the case and the bracelet.

Watch the light: a matte finish changes tone with the lighting, but it stays without mirror reflections. If you see sharp reflections in a photo, it is a different surface. For reading brushed, polished and matte without being fooled: brushed or polished: reading finishes in watch QC photos.

[[PHOTO: primo piano della cassa ottagonale in titanio sabbiato con luce laterale, frecce sugli spigoli tra le sfaccettature, sulla grana uniforme e sulla corona con inserto in ceramica nera]]

Two small but useful details:

  • The crown has the black ceramic insert in the centre: it should be centred, flush and with a clean edge.
  • Weight: one review gives about 68 g for the titanium version. Use that figure with care (it depends on how many links the bracelet has), but if a “titanium” piece weighs like a steel one, the question is fair. Steel and gold versions exist and are heavier, so compare with the right version.

For another titanium watch with the same kind of question on finish and weight: Yacht-Master 42 titanium QC: the matte finish, the bezel and the weight.

On the integrated bracelet: with a watch this flat, the way the bracelet drops from the case matters a lot for how it sits on the wrist. The general discussion of integrated bracelets is here: integrated bracelet on the wrist: Royal Oak and Nautilus in 37, 39 or 41 mm.

On the movement: the sapphire caseback shows the micro-rotor and the layout, but a photo says nothing about how it runs. You need a video of the small-seconds hand and a few days of wear. The original runs at 21,600 vph (3 Hz), less than the usual 4 Hz.

Recap:

  1. Thickness: 5.15 mm on the original, 40 mm diameter; side photo with a calliper at the highest point, glass included.
  2. Movement: BVL 138, 2.23 mm, platinum micro-rotor, 3 Hz, 60 hours; a taller movement forces a taller case.
  3. Finish: sandblasted, matte and even on case, bracelet and dial; no mirror reflections.
  4. Octagon: sharp edges between the facets.
  5. Crown: black ceramic insert centred and flush.
  6. Weight: about 68 g in titanium according to one review; always compare with the same version.
  7. What photos cannot show: comfort on the wrist and how the movement runs.

Editorial summary, not independently verified.

Thanks zaffiro_pignolo, rotore_sincero, occhiodilince and corona_ribelle. I’m asking for the side photo with the calliper straight away.