Lug width vs strap width: odd sizes, taper and why a 20 mm strap may still not fit

A strap listing says “20 mm”. The watch says nothing. Plenty of strap questions start like that, so here is the buying side of it, in one place.

Lug width is the inside gap between the two lugs, at the point where the spring bar sits. It decides the width of the strap at the watch end. It says nothing about the width at the buckle, the thickness, or whether the case takes a normal strap at all.

Three things this thread covers:

  1. Odd widths (19, 21 mm) are real, and the case size does not warn you.
  2. Taper: the strap gets narrower towards the buckle, so the buckle has to match the buckle-end width, not the lug width.
  3. Why “close enough” (20 on 21, 22 on 21) tends to look wrong.

How to read the measurement in someone’s QC photos is a separate question, covered in How to read watch measurements: diameter, lug to lug, thickness and lug width.

[[PHOTO: close-up of the gap between two watch lugs with the strap removed, calipers set at the spring-bar holes, the reading shown in millimetres]]

Not sure about a strap width for your watch? Create an account and ask the community.

Editorial summary, not independently verified.

Okay, naive question. If my reading is 21 mm, a 20 mm strap is only 1 mm off. Who would even see that?

You would. A strap 1 mm too narrow leaves a visible gap at each side of the lugs. One that is 1 mm too wide has to be squeezed in: it bunches against the lugs and the spring bar may not seat properly in its holes.

The usual workarounds are all bad ideas:

  • forcing a strap or bar in (marks the lugs, bends the bar);
  • trimming the strap edges (removes the edge finish, cannot be undone);
  • filing the lugs (permanently changes the case).

If a strap is one size off, the fix is a strap in the right width.

Fine. But are 19 and 21 mm watches actually common, or is my reading just off?

They exist, and the case diameter will not tell you. A few published widths from the makers’ own specifications: the NOMOS Tangente 38 (ref. 166) is 19 mm, the Tissot Gentleman T127.407.11.041.00 is 21 mm, and the Omega Speedmaster Dark Side of the Moon 311.92.44.51.01.005 is 21 mm, while the Moonwatch Professional 310.30.42.50.01.001 is 20 mm. Same family name, different width. A half reading such as 20.5 mm is usually the calipers catching a chamfer or the curve inside a lug: check the maker’s figure for the exact reference, measure again with the strap off at the spring-bar position, and measure a strap that already fits well across its very end.

On taper, which trips people up at the other end:

  • The strap is usually narrower at the buckle than at the lugs. Common pairings for odd widths are 19 mm to 16 mm and 21 mm to 18 mm.
  • The buckle end is never wider than the lug width.
  • Your buckle (or deployant) has to match the buckle-end width. A 21 mm watch with a 21-18 strap needs an 18 mm buckle, not a 21.
  • Taper also changes how the strap looks on the wrist, so compare the buckle-end width, not only the lug width.

[[PHOTO: two straps of the same lug width laid side by side, one tapering from 21 mm to 18 mm and one straight, with the buckle-end width marked on each]]

Changing it without scratching the lugs is its own topic: Changing a watch strap without scratching the lugs: spring bars and lug width.

And the cases where width is not even the main question:

  1. Integrated bracelets and fitted end links: the case is shaped for its own bracelet, so a generic strap may not sit flush. See Oyster and Jubilee bracelets on reps: the clasp, Glidelock, Easylink and end links.
  2. Screw bars or tubes instead of spring bars: the strap has to suit the bar. If you are unsure what holds a bracelet in the first place, screw, split pin or tube: how to tell what holds the links walks through it.
  3. Spring bars and thickness: the bars have to seat fully in the lug holes, and thickness at the lugs is a separate measurement from width.

Summary:

  1. Lug width = the inside gap at the spring-bar position, measured with the strap off. Order exactly that width at the watch end.
  2. Odd widths are normal on some references (19 and 21 mm), whatever the case size. Trust the maker’s figure for the exact reference over a single reading.
  3. One size off (20 on 21, 22 on 21) means gaps or a pinched strap. Do not force, trim or file anything.
  4. Taper: the buckle matches the buckle-end width (21-18 strap, 18 mm buckle).
  5. Before ordering: width at the lugs, width at the buckle, thickness at the lugs, spring-bar type, and whether the case is made for its own bracelet.

Editorial summary, not independently verified.

Thanks strapfiend, claspfiles, braceletgeek, minutetracklab and tick_whisperer. Measuring again with the strap off before ordering anything.