Moon phase on a watch: a 59- or 135-tooth wheel, how to set it and what a QC video can show

Background, from the Fondation de la Haute Horlogerie (FHH) and a Worn & Wound feature.

What it is: an indication that shows the states of the Moon (first quarter, full moon, last quarter, new moon), most often by a disc bearing two moons opposite each other that travel through an aperture, sometimes by a hand or a three-dimensional sphere. The FHH notes that it must not be confused with the age of the Moon, the number of days elapsed since the last new moon.

The difficulty: the synodic month lasts 29 days, 12 hours, 44 minutes and 2.8 seconds, or 29.5305881 days, whereas the gears of a watch turn in 60 minutes, 12 hours or 24 hours.

Practical tip: before any video, identify the display type of the model (disc, hand, sphere).

[[PHOTO: guichet de phase de lune sur un cadran habillé, avec le disque aux deux lunes, les deux « bosses » du guichet et la position de pleine lune indiqués]]

Editorial summary, not independently verified.

A simple question, without jargon: how does a watch follow a 29.5-day cycle if it only counts in hours?

By an elegant approximation. The most common solution, described by the FHH, rounds the cycle to 29.5 days: a 59-tooth wheel corresponds to two lunations (2 × 29.5), and a finger advances it by one tooth every 24 hours. The disc therefore bears two moons, and each completes its “lunation” in 29 and a half days.

The trade-off of this simplicity is a discrepancy: one day every 2 years, 7 months and about 20 days. Worn & Wound cites the ETA/Valjoux 7751 calibre among those that use this arrangement.

And the “astronomical moon” that some spec sheets mention, what is that?

A mini table, from the FHH and Worn & Wound:

System Principle Displayed lunation Discrepancy
59 teeth one tooth per day, two moons 29.5 days 1 day in about 2 years and 7 months
135 teeth 7-pointed star + 16-tooth wheel + 135-tooth wheel 29 d 12 h 45 min 1 day in 122 years and 46 days

The FHH also cites still more precise mechanisms (IWC, A. Lange & Söhne, Andreas Strehler). It is like a staircase: 59 steps a little too high, or 135 steps almost perfect. Practical tip: on the dial, the two systems can look alike; only the model’s spec sheet says which one is fitted.

So what can a QC video show? And what can it not show? To recap:

  • Visible: the disc, its two moons, the aperture, the cleanliness of the printing and of the starry background, the alignment of the moon with the edges of the aperture.
  • Visible with a little patience: the corrector advances the disc, notch by notch.
  • Not visible: the daily jump on a video of a few seconds, since it takes place only once every 24 hours.
  • Not visible at all: long-term accuracy; a video does not distinguish a 2.5-year discrepancy from a 122-year one.

It is the same logic as for other indications seen in a video: Power-reserve indicator: what a QC video shows and what it does not prove. Recap: the look, yes; the accuracy, no.

[[PHOTO: deux captures d’une vidéo de QC côte à côte, avant et après quelques pressions sur le correcteur, avec la position du disque de lune entourée]]

As for setting, it takes a little care. The FHH recalls that a classic moon phase requires a periodic manual correction. Depending on the model, that is done with a corrector or with a position of the crown; the model’s instructions are authoritative. The general method stays the same: place a moon at the centre of the aperture on the day of a known full moon, then advance to today’s date with a lunar calendar. If the moon is driven by the same mechanism as the date, also reread the “danger zone” of the date change before using a corrector.

Summary, with the degree of certainty of the sources:

  1. Display: most often a two-moon disc; not to be confused with the age of the Moon (FHH).
  2. Synodic month: 29 d 12 h 44 min 2.8 s; watches approximate it.
  3. 59-tooth wheel: 29.5 days, one tooth per day, one day off in about 2 years and 7 months; used for example on the ETA/Valjoux 7751 (Worn & Wound).
  4. 135-tooth wheel (“astronomical moon”): one day off in 122 years and 46 days (FHH).
  5. QC video: shows the look and the action of the corrector, not the daily jump in a few seconds nor the long-term accuracy.
  6. Setting: periodic manual correction; corrector or crown according to the instructions; start from a known full moon.
  7. On arrival, the moon phase is checked with the rest: checking a rep watch on arrival.
    Practical tip: note the date of setting, so as to know when to correct.

Editorial summary, not independently verified.

Thanks, clear at last. So a pretty moon in a video says nothing about its accuracy, and setting is done from a known full moon.