The tachymeter scale is one of the most often photographed and least often understood details of a chronograph. Omega describes the function in its product data as follows: a tachymeter is a chronograph with a scale on which a speed in km/h can be read, based on a distance of 1000 meters.
The calculation behind it is simple. The scale value T comes from T = 3600 / t, where t is the stopped time in seconds and 3600 is the number of seconds in an hour. Three things follow from that:
- The scale always shows a mean value, not an instantaneous speed.
- It is unit-independent: kilometres, miles or workpieces, so long as the same unit applies.
- The usual scale is valid only for events of 60 seconds or less; below about 10 seconds it becomes hard to read.
Because the values are spaced according to a fixed formula, every figure on a dial or bezel photo can be checked. That is exactly what this thread is about.
[[PHOTO: Chronographen-Lünette mit Tachymeterskala frontal bei Tageslicht, mit den Werten 60, 120, 180 und 240 und den zugehörigen Sekundenpositionen markiert]]
Editorial summary, not independently verified.
Asked without the jargon: if I start the chronograph and stop it after a given time, does the seconds hand point straight at the speed? And what does “checking the figures” mean on a photo?
Yes, that is the idea. Step by step:
- Start the chronograph at the beginning of a known distance, for example at a kilometre marker.
- Stop at the end of the distance.
- The value next to which the chronograph hand stands is the mean speed in distances per hour.
- Example from the formula: 35 seconds for one kilometre give 3600 / 35 ≈ 103 km/h.
As with a construction drawing and its dimension chains: every number must stand at one quite specific place, otherwise the whole thing is wrong.
One-line takeaway: a tachymeter scale is a table printed around the dial.
And which values belong at which place? Then I could check that myself on every QC photo.
Exactly, and one myth first: a cleanly printed scale “proves” nothing at all about the movement, it only shows whether the graphic is correct! The control table from T = 3600 / t, rounded where needed:
| Seconds (t) |
Scale value (T) |
| 60 |
60 |
| 45 |
80 |
| 40 |
90 |
| 36 |
100 |
| 30 |
120 |
| 24 |
150 |
| 20 |
180 |
| 18 |
200 |
| 15 |
240 |
| 12 |
300 |
| 10 |
360 |
| 9 |
400 |
This is how you read it in the photo: the 120 must sit exactly level with the 30-second mark, that is at 6 o’clock; the 240 level with the 15 seconds, that is at 3 o’clock; the 180 at 20 seconds, that is at 4 o’clock. If a figure sits visibly beside its mark, the scale is printed wrongly or the scale ring is misaligned. How this looks on real references is shown in the threads on the Daytona 126500LN in QC: sub-dials, tachymeter bezel and pushers and on the Speedmaster Moonwatch Professional in QC: stepped dial, the dot above the 90 and Hesalite.
Photo. Check only from the front. Even a slightly oblique angle apparently shifts the figures against the seconds division.
Video. Start the chronograph and stop it after exactly 20 seconds: the hand must stand at 180. That checks the scale and the hand position at the same time.
Limits. Whether the hand jumps back exactly to 12 o’clock after reset is a separate topic. How to tell a column wheel from a cam in a video is in Column wheel or cam: how to tell a chronograph apart in a video.
Who among you checks the scale first, and who checks the hands first?
[[PHOTO: Standbild aus einem Chronographen-Video, Zeiger nach 20 Sekunden angehalten auf dem Tachymeterwert 180, Sekundenteilung und Skala gut lesbar]]
Two short additions:
- Rotatable tachymeter bezels exist as well. The scale can then be aligned with a free-running seconds hand, or used with the minute hand for longer distances. On a photo, what then counts is only whether the values are consistent with one another, not their position relative to 12.
- Measuring a distance also works: at a constant 80 km/h, after 45 seconds, that is when the hand stands at 80, exactly one kilometre has been covered.
Takeaway: on fixed bezels the position relative to the seconds division counts; on rotatable ones, only the spacing.
Summary:
- Formula: scale value T = 3600 / t (t in seconds). Result: mean speed in units per hour, independent of the unit.
- Range: the usual scale is valid for events of 60 seconds or less; below about 10 seconds it is hard to read.
- Control values: 60 at 60 s, 80 at 45 s, 90 at 40 s, 100 at 36 s, 120 at 30 s (6 o’clock), 180 at 20 s (4 o’clock), 200 at 18 s, 240 at 15 s (3 o’clock), 300 at 12 s, 360 at 10 s, 400 at 9 s.
- QC photo: from the front only; every figure must sit on the matching seconds mark. A misplaced figure is a graphic error; a correct scale says nothing about the movement.
- QC video: start, stop after 20 s, hand at 180.
- Rotatable bezels: check only the spacing of the values relative to one another.
- Distance: at constant speed, one unit has been covered when the hand reaches the speed value (80 km/h after 45 s).
Sources: Omega, “Tachymeter” function description in the product data (14 November 2026); Wikipedia, article “Tachymeter (watch)”, formula and examples, retrieved on 14 November 2026.
Editorial summary, not independently verified.
Thank you uhrenfuchs, leuchtguru and zeiger_kenner! My crib sheet: 120 at 6 o’clock, 240 at 3 o’clock, 180 after 20 seconds. And a clean print proves nothing about the movement.